MYROBALAN ~ a tannin used for (pre) mordanting cellulose (Cotton, Linen) Fibres. Recipe below.

ORIGN: India

Myrobalan is a very common tannin used in India and around Asia. It creates a plum-like fruit from various trees of the genus Terminalia, formerly used in medicine as a mild laxative and now used in the dyeing industry.

Myrobalan creates butter yellow on fabric, like most tannins. Tannin is important for mordanting cellulose fibres like cotton and linen. Alum alone is not a suitable mordant for cellulose fibres and its use will produce inferior colours.

Myrobalan can be used in print, over dye with indigo for teal, use as a stand alone colour or as a mordant.

***********************************************

Recipe Downloadable PDF for creating Greys and Charcoal 

Basic recipe for mordanting cellulose fibres:

A 2 step process, please read through the entire instructions first.

Step 1:

Ingredients:

10% Myrobalan (10% of the weight of fabric (w.o.f.))


1.Fill a plastic or stainless steel vessel with hot water (40-50 d. Celcius/100-120F) to a 30:1 ratio (water:fabric)

2. add tannin and stir until dissolved or evenly distributed

3. add fabric, immerse fully for 1-2 hours. The bath will cool down, which is totally fine. Stir occasionally.

4. use rubber gloves when removing fabric, squeeze fabric. Rinse very lightly or better spin it out using a centrifugal spinner or washing machine. Tannin is bound to the fibre only by affinity and can be removed if rinsed aggressively.

5. save mordant for future use.

6. don't let it dry before moving to the 2nd mordanting step.

Step 2:

Ingredients:
Alum 12% (w.o.f.) Dissolved in enough boiling water, cool.
Soda Ash 1.5% (w.o.f.) Dissolve in enough boiling water, cool.

1. Combine the two solutions while stirring. It will bubble, so make sure your vessel is big enough.

2. Bubbles will subside quickly and you should be left with a clear liquid. Add additional hot water as described above. Follow steps 3 - 5 from above.

3. Rinse the textile well, to make sure any unattached mordant is rinsed off.

4. The textile may be dyed immediately or dried for future use.


Tips:

*Too hot and the tannin will oxidize, which is fine, if you want a potentially darker colour. For overdyeing, it is best to keep the colour as light as possible.
** You can also use cold water instead of hot, but it will require a 12h soak at least.
***Any tannin can be used with this recipe, but for lighter results use Oak Gall or Tara.

Enjoy!

Oak Gall - harvested from the wild in Turkey 

Oak Gall, also known as oak apple was and is still used for making ink. We use it as a fibre Mordant, due to its high tannin content. Unlike other tannin, it doesn't stain the fibre.  

Oak Gall is available as whole, cut or ground.

POMEGRANATE PEELS ~ CUT & GROUND ORGANIC ~ can be used as Tannin and as yellow dye

The pomegranate is a fruit-bearing deciduous shrub in the family Lythraceae, subfamily Punicoideae, that grows between 5 and 10 m tall. The pomegranate originated in the region extending from Iran to northern India and has been cultivated since ancient times throughout the Mediterranean region.

 Colourfastness: good - excellent

Recipe:

For how to mordant your Cellulose fibres, please see my blog post 

 How to mordant linen and cotton fabrics successfully – AppleOak FibreWorks

If you are using protein fibres, a simple 10%Alum bath will do for mordanting, but protein fibres can also be dyed without a mordant when using Pomegranate peel due to its tannin content.

Once mordanted:

Add 100% pomegranate peel to 80degrees Celcius Water for one hour. (100% of the dry Weight of your Fibre/Fabric) If using powder, stir regularly or it will burn the bottom of your pan.

After an hour, switch of the heat and add the fabric/fibre. Leave to up to 3 days, until desired depth of colour. 

Wash, rinse, dry.

 Pomegranate Powder can also be used as a tannin and for printing when combined with Alum and Guar Gum.

TARA POWDER ~  is a natural tanning product

Grown in the mountains of Peru.

Tara powder will stain the fibres grey and it is recommended to use a strong dye so the colour isn't too influenced. I am using it for plant dyed flax fibres and LinCot yarns and found, that it actually adds some more depth to the colour.

Basic Recipe:

Please see our blog post on How to mordant linen and cotton fabrics successfully – AppleOak FibreWorks